Accessories to provide various protecting options to the electronic components of an enclosure. Not only is cooling needed in a cabinet but sometimes heat and condensation removal is required. Our accessories provide enhanced cooling capabilities to current products, deliver heating options and allow for the management of potential condensation issues. 

 

 

H2OMIT® Thermoelectric Dehumidifier

Industry Standards

• UL 508A Listed; File No. E61997 cUL Listed per C22.2 No. 14; File No. E61997
• CE

Application

The H2OMIT® Thermoelectric Dehumidifier removes moisture from the air within an enclosure, providing an inexpensive yet highly effective way to protect electronic and electrical components from condensation.

Features

• Reduces corrosion that can limit the life of internal electrical and electronic components
• Condenses moisture from internal enclosure air and standing liquids
• Built-in drain provision with plastic hose directs collected moisture to the Vent Drain (sold separately)
• Rotating side air vents direct recirculating air away from critical controls
• Mounts via DIN rail on internal panel or mounts directly onto the inside bottom of enclosure above the Vent Drain (sold separately)
• Can be used in mild steel, aluminum, stainless steel and non-metallic enclosures

Specifications

• High-impact ABS shell
• Operates on 24-Volt DC power
• 4.5 A max. (84 W)
• Runs continuously above 32 Fa (power supply not included)
• Removes 8 oz. of moisture in 24 hours
• Compact 6.00-in. x 5.50-in. x 5.75-in. design
• One Thermoelectric Dehumidifier includes:
  • Four feet of plastic hose
  • Two hose retainers
  • One double-ended hose retainer
  • Six inches of Velcro®
  • Seven-inch strip of DIN rail
  • Two mounting screws

Must be used with UL-certified drain to remove pooled liquid from enclosure.

*If continual operation is not desired, a Mechanical Hygrostat (AMHUM) can be wired to the thermoelectric dehumidifier and then set to turn the dehumidifier on at the desired relative humidity.

VELCRO is a trademark of Velcro Industries B.V.

H2OMIT® Vent Drains

Industry Standards

Maintains UL/cUL Type 4, 4X rating when properly installed on a UL/cUL Type 4 or 4X enclosure.

• UL 508A Listed; Type 4, 4X; File No. E61997 cUL Listed per CSA C22.2 No 94; Type 4, 4X; File No. E61997
• NEMA/EEMAC Type 4, 4X
• IEC 60529, IP66

Application

H2OMIT® Vent Drains allow accumulated water to drain out the bottom of an enclosure. The UL-approved vent drains also function as an air pressure equalizer, reducing the harmful effects of temperature-induced vacuums that could pull water and moisture into the enclosure.

Features

• Uses gravity to remove collected liquids
• One-way mechanical shut-off when pressure is equalized prevents water and contaminants from entering the enclosure
• Helps reduce corrosion that can limit the life of internal electrical and electronic components
• Installs in a 7/8-in. hole in the bottom of enclosure with provided nut or in a 1/2-in. NPT/NPS threaded conduit hub
• Installs in the bottom of mild steel, aluminum, stainless steel or non-metallic enclosures
• Maintains enclosure’s UL Type rating when properly installed

Specifications

Stainless Steel Vent Drain

• Corrosion-resistant polyester material with a Type 304 stainless steel sleeve
• 2.00-in. long x 1.38-in outside diameter

Non-Metallic Drain Vent

• Corrosion-resistant polyester material
• 2.00-in. long x 1.25-in. outside diameter

 

其他產品至原廠逛逛去.......